Acceptance of consumer rights with the national standard quality wood flooring.

<p> Tip: room decoration is a lot of families have experienced or will have to face things. .Fitting quality problems troubling thing is, this, many people have had personal experience. .Learn some standards related to home improvement, renovation or decoration may be on after being found to have quality problems of consumer rights help. .Introduced today is about the standard of wood flooring, consumers can control their own wood flooring check the quality of eligibility. .</ P> <P> <P> <p> laying quality acceptance criteria </ p> <p> standard wood flooring from a large area, flatness, two floors tenon, tongue and groove connection of the formation, the gap size .acceptance. .</ P> <p> (1) after the laying of a large area in accordance with WB/T1016--2002 flatness standard, solid wood flooring ≤ 5mm, parquet ≤ 3mm. .</ P> <p> determination: If there is no obvious visual rugged usually can. .If special requirements of precision measuring 2m straightedge can be used, the test method: the 2m set to close by the horizontal scale-like, and then by foot from the distance 2m greatest place to plug-foot stuffed, measure out the value is less than .The above data is qualified (test point not less than two per room). .</ P> <p> (2) height difference between stitching stitching stitching height difference is two floors, the height difference. .After laying by WB/1016--2002 standard, solid wood flooring ≤ 0.6mm, wood laminate flooring ≤ 0.2mm </ p> <p> determination: usually measured by visual or foot, that is enough to step on the floor .Without obviously then, if a special request must be precise and accurate, can be affixed to the short straight foot surface of the floor plate will be inserted into plug-foot maximum distance from the ground got the value, is the test value (in the test, each room must also be .two or more). .</ P> <p> (3) splicing splicing gap means the gap of two single blocks of each other after leaving the floor from the assembly, called splicing gap. .Splicing gap size value measure, the use of splicing to measure the gap width, the original State Economic and Trade Commission issued WB/1016--2002 standards, solid wood flooring ≤ 0.6mm, laminate flooring ≤ 0.4mm. .</ P> <p> determination: usually no visual gap, if the dry season during the laying open laying such as Beijing heating requirements can not be too close, too tight to avoid the rainy season, the other defects arising - arch. .Feeler can be inserted into precisely measured, the gap in the chip specifications subject of the Serbian plant, can that gap value. .</ P> <p> laying quality acceptance by WB/T1016--2002 should note the following two aspects: </ p> <p> First, grass-roots acceptance of wood flooring, wood floor surface should be reached before the construction .acceptance can be laid. .</ P> <p> Second, acceptance of the surface layer of wood flooring should be completed within three days after the inspection, more than those at the surface layer during the warranty period for acceptance. .</ P> <p> solid wood floor surface inspection standard warranty </ p> <p> solid wood flooring surface after a week of their acceptance, and WB/T1017--2002 wood by WB/T1016--2002 .floor surface inspection standard warranty period to test, as follows: </ p> <p> laying surface roughness surface roughness to be achieved: solid wood flooring ≤ 6mm; wood flooring ≤ 3mm. .</ P> <p> mosaic flooring Although the height difference through scientific processing, does not produce large changes, but should be a natural property of materials, there will be shrinkage swelling trace changes over the laying of its assembled height difference .surface height difference 0.1mm. .Solid wood flooring ≤ 0.7mm, wood laminate flooring ≤ 0.3mm. .</ P> <p> assembly gap width and gap width of assembling the same reason mentioned above, allowing the wood flooring deviation increase accordingly, while the combination of wood flooring due to structural changes in the variables is small, so the assembly gap width are: solid wood flooring & le .; 2.5mm, parquet ≤ 0.3mm. .</ P>.